CX SUPERCURE AR

  • CX SUPERCURE AR is a non-degrading, membrane forming liquid based on specially formulated acrylic resin suitable for curing newly placed or freshly deshuttered concrete; assists in the retention of water during hydration.
  •  CX SUPERCURE AR is available as a clear translucent liquid and white solar reflective version.

Uses :
• In high-rise construction to eliminate the Requirement for water.
• Surfaces subject to finishing treatments.
• Economical enhancement of concrete flatwork.

Inquiry
Wholesale Bucket Supplier

Download Brochure to view our product

Advantages
right

Reduces shrinkage

Reduces drying shrinkage

right

High efficiency

High curing efficiency.

right

Non– degrading

Non–degrading–no removal required.

right

Improves moisture

Improves moisture retention in concrete.

right

Sealer & dustproofer

Sealer & dustproofer

right

Reduces cracks

Reduces the incidence of hairline cracks.

right

Available in grade

Available in Solar reflective grade.

right

Act as primer

Act as primer for protective coatings & bitumen.

right

Rapid water

Prevents rapid water evaporation.

right

Good abrasion

Good abrasion resistance – long protection.

Properties
propertiesValues
Appearance Clear/white liquid 
Specific gravity Clear 0.82 ± 0.01 at 25º C
White0.855 ±0.01 at 25º C
Flash point30 C
Dry film appearance Dry film appearance
Loss of Water0.55 kg /m2
Drying time45 mins at 25oC
Application

Instructions

  • Application : Stir CX SUPERCURE AR thoroughly before using. Apply a continuous, uniform film by low-pressure spray, short nap roller or brush. Application not recommended when surface temperature exceeds 40 C.
  • Surface Preparation : NEWLY PLACED CONCRETE: • Surface must be sound and properly finished. Surface is ready for application of CX SUPERCURE AR, when damp, but not wet, and it can no longer be marred by foot traffic. NEWLY CURED BARE CONCRETE: • Level any gouges. Remove all dirt, dust, oil, grease, asphalt, and foreign matter. Clean with caustics and detergents as required. Citrus degreaser is excellent for removing oil stains and many curing compounds. Rinse thoroughly and allow to dry. Apply CX SUPERCURE AR to damp but not wet surfaces. AGED CONCRETE : • Restore surface to soundness by patching, grouting, and filling cracks or holes. Surface must also be free of any dust, dirt, and other foreign matter. Use power tools or strippers to remove any incompatible sealers or coatings. Clean as required, following procedure under “Newly cured bared concrete”.
  • Subsequent surface finishes : • The resin in CX SUPERCURE AR ensures that bond is maintained with adhesives used for installing tiles, and other floor coverings. CX SUPERCURE AR will act as a primer for paint systems and will enable most surface treatments to progress with minimal delay. • Typical surface treatments that will bond to surfaces with CX SUPERCURE AR are: • Water based emulsion paints containing PVA, PVC and acrylic co-polymers • Tile adhesives based on the above polymers • Bituminous emulsions and solutions. • Thin section polymer modified cementitious systems. • Polyurethane resin system • Polysulphide systems • Epoxy resin compositions which do not rely onpenetration for substrate bond.

Estimating

  • Packaging : 50 kg 250 kg
  • Storage : CX SUPERCURE AR must be stored where temperatures do not drop below +5°C. Store under cover, out of direct sunlight and protect from extremes of temperature. Shelf life is12 months when stored as above.
  • Coverage : • The recommended rate of application is 4-6 square metres per litre. This corresponds to that at which CX SUPERCURE AR has been tested, and at which it attains the claimed degree of curing efficiency. In favourable conditions such as shaded interior surfaces, adequate curing can be achieved with extended coverage rates. • When using CX SUPERCURE AR for floor areas where maximum chemical and wear resistance is required, it is recommended that a further coat be applied after 24 hours. • In place of the above recommendations, the rates of cover stipulated in a specification should at all times be observed.

Precautions

  • Precautions : • As with all chemical products, care should be taken during use and storage to avoid contact with eyes, mouth, skin and foodstuffs (which can also be tainted with vapour until product fully cured or dried). • Treat splashes to eyes and skin immediately. • If accidentally ingested, seek immediate medical attention. • Keep away from children and animals. • Reseal containers after use. • Do not reuse containers for storage of consumable item.
  • Health & Safety instructions : CX SUPERCURE WB is non toxic. It is advisable to wear goggles when spraying. Inhalation of the spray should similarly be avoided. Should skin contact with the compound occur it shall be washed with clean water and a skin conditioning cream shall be applied. If CX SUPERCURE WB comes into contact with eye sit shall be washed with clean water. If irritation persists, immediate medical attention shall be sought. If the compound is swallowed, vomiting should not be induced but medical assistance shall be obtained immediately.
  • Fire : CX SUPERCURE WB is water based and non flammable
Chemax AR Application
Newer CX Fast Set P+
Back to list
Older CHEMAX GROUT A01

Related Projects

  • Accelerators & Concrete Block Admixture
  • Concrete Admixture

CX Fast Set P+

  • Concrete Admixture
  • High Range Water Reducing Admixture (Super Plasticizer)

CHEMAX GROUT A01

  • Concrete Admixture
  • High Range Water Reducing Admixture (Super Plasticizer)

CX AIR ENTRAINING